View source for AVR Library Usage Guide ← AVR Library Usage Guide

*''Below example demonstrates the step by step procedure to include the libraries into any applications.''
'''Step 1:''' ''Open the Avr AtmelStudio-6 and select the New project from File Menu as shown below.''
[[File:1Open_AvrAtmel.png|720x480px]]

'''Step 2:''' ''Browse to your project folder and provide the project name and click on Ok.''
[[File:2Give_ProjName.png|720x480px]] 

[[File:2.1Give_ProjName.png|720x480px]]

[[File:2.2Give_ProjName.png|720x480px]]

'''Step 3:''' ''Once the project is saved a new dialog box “Device Selection” opens, Select Atmega32 and click OK.''
[[File:3Device_Selection.png|720x480px]]

'''Step 4:''' ''Once the project is successfully created the below window opens with the initil .c file .''<br\>
''Note:''
*''The initial file name will be same as project name.''
[[File:4Initial_CFile.png|720x480px]]

'''Step 5:''' ''Write your program using the library functions and save it.<br\>
''Note:''
*''Include the respective header files before calling any library functions.''
[[File:5Write_program.png|720x480px]]

'''Step 6:''' ''Add the library files(.c,.h) to the project as shown below.''
''Note:''
*''Copy the library files into the project folder before including them into the project.''
[[File:6Add_LibraryFiles.png|720x480px]]

'''Step 7:''' ''Add the Source(.c) and header( .h)  files by browsing to the project folder.''
[[File:7Include_srcHeaderfile.png|720x480px]] 

'''Step 8:''' ''The included library files can be seen in Solution Explorer on the right side.''
[[File:8Include_LibraryFiles.png|720x480px]]

'''Step 9:''' ''Compile the project by clicking on Build Solution from Build menu (or press F7). Project complies if there are no errors. If there are any errors fix them and re-compile.''
[[File:9Compile_Project.png|720x480px]]

[[File:9.1Build_Project.png|720x480px]]

'''Step 10:''' ''Configure the Controller Freq by selecting the project properties from Project menu.''<br\>
''Note:''
*''As the Inbuilt delay routines as used the freq needs to be specified to generate accurate delays.''
[[File:10Configure_Frequency.png|720x480px]]

'''Step 11:''' ''Select the Symbols from Tool Chain menu and Click on Add Item in Defined Symbols(-D) box.''
[[File:11Select_Symbol.png|720x480px]]

'''Step 12:''' ''Provide the Controller (Target Board) frequency as F_CPU=xxx Hz .In this case it is 11.0592Mhz.''
[[File:12TargetBoard_Frqncy.png|720x480px]]

'''Step 13:''' ''Configuring the optimization levels: Select the Optimization from ToolChain menu. Select the required optimization level from drop down. Refer WinAvr/Gcc documents for more optimization details.''
[[File:13Configure_Optimization.png|720x480px]]

'''Step 14:''' ''Seletcting the targed tool chain : Select the Advanced option on the left side, now click the link shown in blue colour”Tools->Options->Toochain ->Flavour Configuretion“.''
[[File:14Target_ToolChain.png|720x480px]] 

'''Step 15:''' ''From the drop down select WinAVR and set it as Default toolchain by clicking on “Set As Default”.''
[[File:15Select_WinAVR.png|720x480px]]<br\>
''Note:''
*''Above two Steps( 14 & 15) needs to be performed for the first time, ie till the WinAVR is configured as default Toolchain .''

'''Step 16:''' ''Finally recompile after all configurations. Hex file will be generated with the project name in the selected '''Project->Debug folder.''' ''
[[File:16Recompile_Project.png|720x480px]]