(11 intermediate revisions by 3 users not shown)
Line 1: Line 1:
 
[[Category:Starter PIC16F877]]
 
[[Category:Starter PIC16F877]]
We will see in this tutorial how to upload hex file using DS30 loader GUI
+
[[Category:oneMicro PIC16F877A]]
=Installing DS30 Loader GUI=
+
We will see in this tutorial how to upload hex file to PIC controller using DS30 loader GUI.<br><br>
For installing DS30 Loader GUI we need to download the below mentioned DS30 Loader GUI software. <br>
+
* [http://exploreembedded.com/wiki/File:Ds30LoaderGui.zip DS30 Loader GUI software] <br>
+
  
=Launching  DS30 Loader GUI software=
+
 
* Once we download the DS30 Loader GUI software, start the DS30 Loader GUI software by selecting Start>Programs>DS30 loader GUI .  
+
=Installing DS30 Software=
 +
Download the DS30 Loader Software from the below link and Extract it to some folder.<br>
 +
* [http://exploreembedded.com/wiki/images/7/7e/Ds30LoaderGui.zip DS30 Loader GUI software] <br><br><br>
 +
 
 +
=Launching  DS30 Loader =
 +
Run the DS30 Loader GUI software  .  
  
 
Step 1:  
 
Step 1:  
[[File:DS30 window.png|none]]
 
*Browse the hex file
 
*Select the appropriate MCU
 
*'''Select the baud rate as 9600'''
 
*'''Select the correct com port detected on your computer, when using USB to serial convertor check for exact COM port number in device manager'''
 
  
Step 2: The board uses DTR pin of the CP2102 USB to Serial Convertor to reset the MCU. Set it up as shown in the image below.
+
#Browse the hex file
 +
#Select the appropriate MCU
 +
#Select the baud rate as 9600
 +
#Select the correct com port detected on your computer, when using USB to serial converter check for exact COM port number in device manager.
 +
[[File:DS30 window.png|none]]<br><br>
 +
 
 +
Step 2: The board uses DTR pin of the CP2102 USB to Serial Converter to reset the MCU. Set it up as shown in the image below.
 +
[[File:DS30 loader settings.png|none]]<br><br>
 +
 
 +
Step 3: Click on the '''write''' option to flash the hex file. Once hex file is successfully uploaded status window display '''Write successfully completed''' Refer below image.
 +
[[File:0DS30 loader successfully.png|none]]<br><br>
  
[[File:AUTO RESET.png|x300px|Setup AutoReset]]
 
  
Step 3: Click on the '''write''' option to flash the hex file. Once hex file is successfully uploaded status window display '''Write successfully completed'''Refer below image.
+
Have a opinion, suggestion , question or feedback about the article let it out here!
[[0File:DS30 loader successfully.png|none]]
+
{{DISQUS}}

Latest revision as of 13:43, 9 September 2016

We will see in this tutorial how to upload hex file to PIC controller using DS30 loader GUI.


Installing DS30 Software

Download the DS30 Loader Software from the below link and Extract it to some folder.

Launching DS30 Loader

Run the DS30 Loader GUI software .

Step 1:

  1. Browse the hex file
  2. Select the appropriate MCU
  3. Select the baud rate as 9600
  4. Select the correct com port detected on your computer, when using USB to serial converter check for exact COM port number in device manager.
DS30 window.png


Step 2: The board uses DTR pin of the CP2102 USB to Serial Converter to reset the MCU. Set it up as shown in the image below.

DS30 loader settings.png


Step 3: Click on the write option to flash the hex file. Once hex file is successfully uploaded status window display Write successfully completed Refer below image.

0DS30 loader successfully.png



Have a opinion, suggestion , question or feedback about the article let it out here!