(6 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 
[[Category:8051 Development Boards]]
 
[[Category:8051 Development Boards]]
 +
[[File:Cart add.png|right|link=https://www.exploreembedded.com/product/Starter%20SST89E516RD%20USB%20Development%20board]]
 
{{Popup|type=l|text= ''This is latest 8051 Starter Development board from Explore Embedded, the board uses '''SST89E512RD''' Microcontroller which is '''100%''' compatible with '''P89V51RD2'''. The board has USB to Serial Convertor which can be used to program/flash the MCU; eliminates need for a programmer. It can used with laptops as well!''}}
 
{{Popup|type=l|text= ''This is latest 8051 Starter Development board from Explore Embedded, the board uses '''SST89E512RD''' Microcontroller which is '''100%''' compatible with '''P89V51RD2'''. The board has USB to Serial Convertor which can be used to program/flash the MCU; eliminates need for a programmer. It can used with laptops as well!''}}
 +
[[File:DSC09000.JPG|x480px]]
 +
<gallery mode="packed">
 +
File:DSC09010.JPG
 +
File:DSC09023.JPG
 +
File:DSC01041.JPG
 +
</gallery>
 
{{Box|type=l_green_light|text = '''Features'''}}
 
{{Box|type=l_green_light|text = '''Features'''}}
 
{{Box|type=l_green_light|text = <br/>
 
{{Box|type=l_green_light|text = <br/>
Line 46: Line 53:
 
*[http://exploreembedded.com/wiki/images/c/cb/EasyIAP_Rev_6.0.zip Download EasyIAP] and install it.
 
*[http://exploreembedded.com/wiki/images/c/cb/EasyIAP_Rev_6.0.zip Download EasyIAP] and install it.
 
*Follow the steps in the pictures below to detect the board and flash the hex file
 
*Follow the steps in the pictures below to detect the board and flash the hex file
 +
}}
 +
[[File:7 Flash.JPG|framed|x400px|Follow steps in images below:]]
 
<gallery>
 
<gallery>
File:0_device manager.jpg
+
File:0_device manager.JPG
File:1_Install SW.jpg
+
File:1_Install SW.JPG
File:3_setup.jpg
+
File:3_setup.JPG
File:4_connect.jpg
+
File:4_connect.JPG
File:5_Browse.jpg
+
File:5_Browse.JPG
File:6_OK.jpg
+
File:6_OK.JPG
File:7_Flash.jp
+
File:7 Flash.JPG
 
</gallery>
 
</gallery>
 
+
=8051 Video Tutorials=
}}
+
And that's not all watch this complete series of 8051 video tutorials, which we believe should definitely  help you build
 +
{{#widget:YouTube|playlist=PLRuRKN7_FVgtdXWWM-uosWYfmOFDp63dd|width=680}}
 +
{{DISQUS}}

Latest revision as of 18:41, 6 March 2015

Cart add.png

This is latest 8051 Starter Development board from Explore Embedded, the board uses SST89E512RD Microcontroller which is 100% compatible with P89V51RD2. The board has USB to Serial Convertor which can be used to program/flash the MCU; eliminates need for a programmer. It can used with laptops as well!
DSC09000.JPG

Features


  • SST89E516RD Microcontroller with bootloader (no programmer needed)
  • CP2102 USB to Serial Convertor on board
  • 16 x 2 LCD Interface
  • Switches x2
  • LEDs x2
  • All Ports pins as breakout.
  • High quality FR4 , wave soldered PCB.

SST89E516RD MCU Features


  • 1 KByte Internal RAM
  • Dual Block SuperFlash EEPROM– 64 KByte primary block +8 KByte secondary block
  • Support External Address Range up to 64KByte of Program and Data Memory
  • Three High-Current Drive Ports (16 mA each)
  • Three 16-bit Timers/Counters
  • Full-Duplex, Enhanced UART– Framing Error Detection– Automatic Address Recognition
  • Ten Interrupt Sources at 4 Priority Levels– Four External Interrupt Inputs
  • Programmable Watchdog Timer (WDT)
  • Programmable Counter Array (PCA)
  • Four 8-bit I/O Ports (32 I/O Pins) andOne 4-bit Port
  • Second DPTR register
  • Low EMI Mode (Inhibit ALE)
  • SPI Serial Interface
  • Standard 12 Clocks per cycle, the device has adoption to double the speed to 6 clocks per cycle.
  • TTL- and CMOS-Compatible Logic Levels
  • Brown-out Detection
  • Low Power Modes– Power-down Mode with External Interrupt Wake-up– Idle Mode

Downloads

Setting up EasyIAP SW and programming the hex file


  • Connect the Board to the computer and install Windows USB to UART Drivers for CP2102.
    • Note: Power up the board with 7 to 12V, 1A adapter, the board does not power up from USB.
  • Note down the COM Port Number e.g. COM 2 from device manager
  • Download EasyIAP and install it.
  • Follow the steps in the pictures below to detect the board and flash the hex file
Follow steps in images below:

8051 Video Tutorials

And that's not all watch this complete series of 8051 video tutorials, which we believe should definitely help you build {{#widget:YouTube|playlist=PLRuRKN7_FVgtdXWWM-uosWYfmOFDp63dd|width=680}}