Difference between revisions of "Serial Communication with PIC16F877A"
| Line 34: | Line 34: | ||
<b>CSRC:</b> Clock Source Select bit<br> | <b>CSRC:</b> Clock Source Select bit<br> | ||
Asynchronous mode:Don’t care. | Asynchronous mode:Don’t care. | ||
| − | |||
<b>TX9:</b> 9-bit Transmit Enable bit<br> | <b>TX9:</b> 9-bit Transmit Enable bit<br> | ||
| Line 48: | Line 47: | ||
1 = Synchronous mode<br> | 1 = Synchronous mode<br> | ||
0 = Asynchronous mode | 0 = Asynchronous mode | ||
| − | |||
<b>BRGH:</b> High Baud Rate Select bit<br> | <b>BRGH:</b> High Baud Rate Select bit<br> | ||
1 = High speed<br> | 1 = High speed<br> | ||
0 = Low speed<br> | 0 = Low speed<br> | ||
| − | |||
<b>TRMT:</b> Transmit Shift Register Status bit | <b>TRMT:</b> Transmit Shift Register Status bit | ||
Revision as of 10:51, 5 May 2016
In this tutorial we are going to discuss the serial/UART communication using PIC16F877A.
PIC16F877A comes with inbuilt USART which can be used for Synchronous/Asynchronous communication. We will be discussing only the UART. After understating the basics of PIC16F877A UART module, We will see how to use the ExploreEmbedded libraries to communicate with any of the UART devices.
UART Registers
The below table shows the registers associated with PIC16F877A UART.
| Register | Description |
|---|---|
| TXSTA | Transmit Status And Control Register |
| RCSTA | Receive Status And Control Register |
| SPBRG | USART Baud Rate Generator |
UART Register Configuration
Now lets see how to configure the individual registers for UART communication.
| TXSTA | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| CSRC | TX9 | TXEN | SYNC | - | BRGH | TRMT | TX9D |
CSRC: Clock Source Select bit
Asynchronous mode:Don’t care.
TX9: 9-bit Transmit Enable bit
1 = Selects 9-bit transmission
0 = Selects 8-bit transmission
TXEN: Transmit Enable bit
1 = Transmit enabled
0 = Transmit disabled
Note: SREN/CREN overrides TXEN in Sync mode.
SYNC: USART Mode Select bit
1 = Synchronous mode
0 = Asynchronous mode
BRGH: High Baud Rate Select bit
1 = High speed
0 = Low speed
TRMT: Transmit Shift Register Status bit
1 = TSR empty
0 = TSR full
TX9D: 9th bit of Transmit Data, can be Parity bit
| RCSTA | |||||||
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
| SPEN | RX9 | SREN | CREN | ADDEN | FERR | OERR | RX9D |
SPEN: Serial Port Enable bit
1 = Serial port enabled (configures RC7/RX/DT and RC6/TX/CK pins as serial port pins)
0 = Serial port disabled
RX9: 9-bit Receive Enable bit
1 = Selects 9-bit reception
0 = Selects 8-bit reception
SREN: Single Receive Enable bit
Asynchronous mode:Don’t care.
CREN: Continuous Receive Enable bit
Asynchronous mode:
1 = Enables continuous receive
0 = Disables continuous receive
ADDEN: Address Detect Enable bit
Asynchronous mode 9-bit (RX9 = 1):
1 = Enables address detection, enables interrupt and load of the receive buffer when RSR is set
0 = Disables address detection, all bytes are received and ninth bit can be used as parity bit
FERR: Framing Error bit
1 = Framing error (can be updated by reading RCREG register and receive next valid byte)
0 = No framing error
OERR: Overrun Error bit
1 = Overrun error (can be cleared by clearing bit CREN)
0 = No overrun error
RX9D: 9th bit of Received Data (can be parity bit but must be calculated by user firmware)