Revision as of 18:05, 14 April 2016

In this tutorial we'll interface stepper motor with Starter AVR board using A4988 driver. For driving one stepper motor, one A4988 driver is required. A4988 has inbuilt translator so we can control this driver by just two pins, one for direction and one for controlling the steps.

Basic

A4988 comes with an output drive capacity of up to 35 V and ±2 A and compatible with 3.3V and 5V logic supply. A4988 is a 16 pin driver as shown in following figure. We'll look at all pins and it's functioning one by one.

First two pins are Direction and Step which are actually used to control the movement of stepper motor. Direction pin will control the direction of motor, making this pin high will move motor in clockwise direction whereas making this pin low will move motor in anti-clockwise direction. For moving motor we have to simply give pulses to Step pin. Inputting one pulse on the STEP input drives the motor one microstep.
Third pin is SLEEP pin, which will be used to put driver in sleep mode whenever driver is not in use. Next pin is RESET pin. If we input logic low to this pin then all step signals will be ignored, so to enable the board this pin should be pulled high. As this pin is floating, if you don't want to control it with controller just connect it to SLEEP pin in order to enable the board as SLEEP pin is pulled high on board.
Next three pins are important as these three pins are used for micro stepping. Connect MS1, MS2 and MS3 as per following table to get particular step resolution. If you want to use motor in full step just keep them unconnected.
Next pin is Enable pin, which will turn on and off outputs. So make this pin low to enable output.
Next two pins VMOT and GND are for powering up the stepper motor. We can connect it to power supply from 8V to 35V, in our case we connected these pins to 12V supply. If you are using unregulated power supply then connect 47uF capacitor to protect driver against voltage spikes. After that next four pins are for connecting motor. 2A and 2B will be connected to one coil whereas 1A and 1B will be connected to another coil of stepper motor. Last two pins are for powering up the driver VDD and GND. We can connect it to either 3.3v or 5V, in our case we connected it to 5V supply.

After powering up the driver, the main thing to be done is setting the current limiting potetiometer on board as shown in figure, which will limit the current through the driver.

Rotating pot in clockwise direction will increase the current through the driver. We can do the current adjustment by adjusting the reference voltage VREF using potentiometer  and  using the following equation:

$$ Maximum Current = VREF / (8 * Rs)$$
Where, Rs = 0.1 for A4988
Now, measure VREF as shown in figure. In our case I adjusted it to 0.6V so Maximum Current becomes 0.75A. Now as per A4988 datasheet winding current could reach up to only 70% of Maximum Current in full step mode that is in our case, $$0.7 * 0.75 = 0.525A $$

Hookup

Code

Demo

For full demo video visit our youtube channel https://www.youtube.com/watch?v=fYsiDZhr1ZU&feature=youtu.be

Downloads

@@ Line 18: / Line 18: @@
 <br />
 <br />
-After powering up the driver, the main thing to be done is setting the current limiting potetiometer on board as shown in figure, which will limit the current through the driver.
+After powering up the driver, the main thing to be done is setting the current limiting potetiometer on board as shown in figure, which will limit the current through the driver.<br />
 [[file:Stepper Starter AVR.JPG]]
+<br />
   Rotating pot in clockwise direction will increase the current through the driver. We can do the current adjustment by adjusting the reference voltage '''VREF''' using potentiometer  and  using the following equation:
 <br />
@@ Line 26: / Line 29: @@
 Where, Rs = 0.1 for A4988
 <br />
-Now, measure  VREF as shown in figure. In our case I adjusted it to 0.6V so Maximum Current becomes 0.75A. Now as per A4988 datasheet winding current could reach up to only 70% of Maximum Current in full step mode that is, $$0.7 * 0.75 = 0.525A $$ in our case.
+Now, measure  VREF as shown in figure. In our case I adjusted it to 0.6V so Maximum Current becomes 0.75A. Now as per A4988 datasheet winding current could reach up to only 70% of Maximum Current in full step mode that is in our case, $$0.7 * 0.75 = 0.525A $$
 [[file:Vref Starter AVR.JPG]]

Difference between revisions of "Interfacing Stepper Motor with Starter AVR Using A4988"