I am obsessed with numbers, are you? Examples in the demo are frivolous but the objective is to display that numbers that matter on a tiny OLED from all over the internet(sort of)!

We will be using services like IFTTT (which did not work well), Zapier (trial plan) etc to fetch numbers from numerous services out there and show them on a tiny display. We will be using the hornbill ESP32 Minima to connect to the internet (AWS IOT). We will expose a webhook on our server to receive the trigger and then publish the message to display. Confused? Looking at the image below might help. 0 FICD.jpg This may not be the best appoach to do this, but this is what I could come up with you. If you can think of anything better, please do comment!

The Parts

  • Hornbill ESP32 Minima
  • OLED 128x64
  • Wires
  • Plastic enclosure
  • LiPo Battery

4 FICD.jpg

The Build

Measure the OLED size, mark it on the enclosure and make a cut out. We did it with a bench top drill. Start out by drilling small holes along side the marking.

1 FICD.jpg

File the rough edges to make a smooth cut out.

2 FICD.jpg

We plan to power it up with the LiPo battery. If you plan to use a USB charger, you might want to make one more cut out for it.

3 FICD.jpg

The Hornbill Minima comes with the LiPo battery connector. Only 4 connections are to be made for the display.

OLED Pin ESP32 Pin Description
SDA 21 Yellow wire
SCL 22 White wire
VCC 3.3V Red Wire
GND GND Black wire

Start with with soldering the wires on OLED first.

5 FICD.jpg

6 FICD.jpg

7 FICD.jpg

Then solder the wires on the Hornbill Minima Pads.

8 FICD.jpg

Now make appropriate changes in the firmware code. Download from the "code for FICD section"

9 FICD.jpg

Now, its is time to mount the display inside the case. We did this with the help of tape. You might design and print a tiny 3D printed case as well.

10 FICD.jpg

11 FICD.jpg

12 FICD.jpg

13 FICD.jpg

14 FICD.jpg

15 FICD.jpg

Now the display is ready for action. It will display hard-coded numbers from the firmware. In the next section we will look at using services like IFTTT and Zapier, to display numbers that matter.

Let us look at the data will flow throughout the example.

Attribute Example Value Description
service twitter Name of the service, this should match in the Arduino code
serviceTag followers This will be displayed in small font. It could be anything that describes the next attribute.
value 231 The value shown in big font on the display. It can be a formatted number or string.


Setting up the trigger Services

These services all triggers to be set up from various other services online. We tried IFTTT and Zapier in this tutorial. The IFTTT maker channel did not work well. Zapier did work well. You may try these or any other similar services as well. Note that the free plan for Zapier is limited. Opening an account and setting up a trigger is pretty straightforward and for that reason I'll skip those steps.

With all these services we will set up a HTTP POST request to be made whenever the event occurs. In the example below I configure a POST action if a new twitter search appear with a certain name. 16 FICD zapier 1.jpg

You can get creative with the trigger part, it could be email, Instagram, Stocks, Time, Weather etc., I will cover the action part in detail. The end goal of the action part is to take the configured values and publish them on the display. However there is no direct way to do that. The trigger services use HTTP and our devices on Hornbill IO/ AWS IOT speak MQTT. Hence we need to write a small script to handle the post and publish the message to the display. I will cover this in the next section. Let us look at the action part now.

17 FICD zapier 2.jpg

The URL handles the POST request with the fields described in the table above. The code for handling the post and publishing the message to device is described in the next section. The URL used in the example is disabled and you'll have to make one if needed. Also note that the triggers if not set properly can publish millions of messages which will cost a lot of money. So be sure to set them up properly.

Code on Web Server

In this section we will look at handling the POST data from the previous step and publishing the payload to the device. We use a node server with AWS IOT library to achieve this. You may as well use service like AWS lambda to achieve the same.

Code on the ESP32 Hardware

The code requires several configurations to work. Check the tutorials listed in the beginning of the code for details on setting up AWS IOT and using it with simpler examples first.

With this code you'll have to first set up the AWS Configuration

/************************************************************************
                             AWS Configuration
/************************************************************************/
char WIFI_SSID[]="your Wifi SSID";
char WIFI_PASSWORD[]="Wifi Password";
char HOST_ADDRESS[]="AWS host address";
char CLIENT_ID[]= "client id";
char TOPIC_NAME[]= "your thing/topic name";
/***********************************************************************/

Also the services to be displayed need to configured.

typedef enum{
    SERVICE_TWITTER,
    SERVICE_FACEBOOK,
    SERVICE_TIME,
    SERVICE_TEMPERATURE,
    SERVICE_MAX_OPTIONS
};

Lastly, the bitmaps for the logs will also have to updated according to the service used.

The complete source code is listed below. <script src="https://gist.github.com/Xplorer001/edde357e719c1ebec42ea69d936670fd.js"></script> </html>