Revision as of 20:12, 22 October 2013

Introduction

Overview:

This manual is designed to help embedded programmers and students, rapidly exploit the Avr(Atmega)-Controller for embedded applications. This manual has been targeted at embedded systems programmers and Students who have basic knowledge of Avr(Atmega32/Avr) architecture and C-Language.

This manual provides the reference to all the library functions which are grouped under respective .c file.

The .c files convention is as per the peripherals. The peripherals (lcd, keypad..) are connected to default PORTs which can be connect to required  PORTs by changing the #defines .

Reference:

    It is recommended to go through the below reference documents and datasheets before interfacing any peripherals.

1. The Avr Microcontroller and Embedded Systems by Muhammad Ali Mazidi. 2. Atmega32 DataSheet. 3. Embedded C by Michael J Pont . 4. Any of the 16x2 lcd datasheet. 5. RTC-DS1307 from Dallas Semiconductors.

Feedback:

Suggestions for additions and improvements in code and documentation are always welcome. Please send your feedback via e-mail to feedback@xplorelabz.com

Disclaimer:

The libraries have been tested for Atmega16 on different development boards. We strongly believe that the library works on any Atmega boards. However, Xplore Labz disclaims any kind of hardware failure resulting out of usage of libraries, directly or indirectly. Documentation may be subject to change without prior notice.

The usage of tools and software demonstrated in the document are for educational purpose only, all rights pertaining to these belong to the respective owners. Users must ensure license terms are adhered to, for any use of the demonstrated software.

Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.

Since the library is licensed free of charge, there is no warranty for the libraries and the entire risk of the quality and performance is with the user.

Errors and omissions should be reported to feedback@xplorelabz.com

ADC

                                   Avr ADC library

Filename: adc.c
Controller: Atmega8/16/32/128
Oscillator: 11.0592 MHz
Author: XploreLabz
website: www.xplorelabz.com
Reference:Atmega32 dataSheet

#include<avr/io.h>
#include <util/delay.h>
#include "adc.h"

ADC_Init()

Description :This function initializes the ADC control registers
I/P Arguments: none
Return value: none

void ADC_Init()
 {
   ADCSRA=0x81;  //Enable ADC , sampling freq=osc_freq/2
   ADMUX=0x00;   //Result right justified, select channel zero
  }

ADC_StartConversion()

Description :This function does the ADC conversioin for the Selected Channel and returns the converted 10bit result
I/P Arguments: char(channel number)
Return value : int(10 bit ADC result)

 
unsigned int ADC_StartConversion(unsigned char channel)
 {
   ADMUX=channel;         
   _delay_ms(5);           
   ADCSRA=0xc1;           
   while((ADCSRA & (1<<ADIF)==0); 
    return(ADCW);
 }

LCD_8_bit Mode

                       AVR LCD library for 8-bit mode

Filename: lcd_8_bit.c
Controller: Atmega Family(8,16,32,64,128)
Oscillator: 11.0592 MHz
Author: XploreLabz
website: www.xplorelabz.com

Note:

Pin connection for LCD display in 8-bit mode is as shown below.By default the LCD is connected to PORTB(databus) and PORTD(controlbus).
The code can be modified to connect the LCD to any of the PORTs by changing the "#define".
io.h contains the defnition of all ports and SFRs delay.h contains the in built delay routines(us and ms routines).

#include <avr\io.h>
#include <util\delay.h>
 
#include "lcd.h"
 
#define databus_direction DDRC      //  LCD databus Direction Configuration
#define controlbus_direction DDRD  //  LCD Control bus Direction Configuration
 
#define databus	PORTC             //	LCD databus connected to PORTB
#define control_bus PORTD        //	LCD Control bus connected to PORTD
 
#define rs 5                    // Register select pin connected 6th bit(D5) Control bus
#define rw 6                   // Read Write pin connected to 7th bit(D6) Control bus
#define en 7                  // Enable pin connected to 8th bit(D7) Control bus
 
 
/* 16x2 LCD Specification */
#define LCDMaxLines 2
#define LCDMaxChars 16
#define LineOne 0x80
#define LineTwo 0xc0
 
#define BlankSpace ' '

LCD_Init()

Description :This function is used to initialize the lcd in 8-bit mode
Function name: LCD_Init()
I/P Arguments: none.
Return value : none

void LCD_Init()
{
    _delay_ms(50);
   databus_direction = 0xff;   // Configure both databus and controlbus as output
   controlbus_direction = 0xff;
   LCD_CmdWrite(0x38);   // LCD 2lines, 5*7 matrix
   LCD_CmdWrite(0x0E);	// Display ON cursor ON
   LCD_CmdWrite(0x01);	// Clear the LCD
   LCD_CmdWrite(0x80);	// Move the Cursor to First line First Position
}

LCD_Clear()

Description :This function clears the LCD and moves the cursor to first Position
I/P Arguments: none.
Return value : none

void LCD_Clear()
{
   LCD_CmdWrite(0x01);	// Clear the LCD and go to First line First Position
   LCD_CmdWrite(LineOne);
}

LCD_GoToLineOne()

Description :This function moves the Cursor to First line First Position
I/P Arguments: none
Return value : none

void LCD_GoToLineOne()
{
   LCD_CmdWrite(LineOne);	// Move the Cursor to First line First Position
}

LCD_GoToLineTwo()

Description :This function moves the Cursor to Second line First Position
I/P Arguments: none
Return value : none

void LCD_GoToLineTwo()
{
   LCD_CmdWrite(LineTwo);	// Move the Cursor to Second line First Position
}

LCD_GoToXY()

Description :This function moves the Cursor to specified position
I/P Arguments: char row,char col
- row -> line number(line1=0, line2=1),For 2line LCD the I/P argument should be either 0 or 1.
- col -> char number.For 16-char LCD the I/P argument should be betwen 0-15.
Return value : none

void LCD_GoToXY(char row, char col)
{
   char pos;
 
    if(row<LCDMaxLines)
      {
		 pos= LineOne | (row << 6); // take the line number
		                            //row0->pos=0x80  row1->pos=0xc0
 
	    if(col<LCDMaxChars)
		   pos= pos+col;            //take the char number
		                            //now pos points to the given XY pos
 
		 LCD_CmdWrite(pos);	       // Move the Cursor to specified Position
       }
}

LCD_CmdWrite()

Description :This function sends a command to LCD in the following steps.
- step1: Send the I/P command to LCD.
- step2: Select the Control Register by making RS low.
- step3: Select Write operation making RW low.
- step4: Send a High-to-Low pulse on Enable PIN with some delay_us.
I/P Arguments: 8-bit command supported by LCD.
Return value : none

void LCD_CmdWrite( char cmd)
{
 
    databus=cmd;             // Send the command to LCD
    control_bus &=~(1<<rs);  // Select the Command Register by pulling RS LOW
    control_bus &=~(1<<rw);  // Select the Write Operation  by pulling RW LOW
    control_bus |=1<<en;     // Send a High-to-Low Pusle at Enable Pin
   _delay_us(1);
   control_bus &=~(1<<en);
   _delay_ms(1);
}

LCD_DataWrite()

Description:This function sends a character to be displayed on LCD in the following steps.
- step1: Send the character to LCD.
- step2: Select the Data Register by making RS high.
- step3: Select Write operation making RW low.
- step4: Send a High-to-Low pulse on Enable PIN with some delay_us.
I/P Arguments: ASCII value of the char to be displayed.
Return value : none

void LCD_DataWrite( char dat)
{
 
    databus=dat;            // Send the data to LCD
    control_bus |=1<<rs;	// Select the Data Register by pulling RS HIGH
    control_bus &=~(1<<rw);	// Select the Write Operation  by pulling RW LOW
    control_bus |=1<<en;	// Send a High-to-Low Pusle at Enable Pin
	_delay_us(1);
    control_bus &=~(1<<en);
    _delay_ms(1);
 
}

LCD_DisplayString()

Description :This function is used to display the ASCII string on the lcd.

The string_ptr points to the first char of the string and traverses till the end(NULL CHAR).
Each time a char is sent to LCD_DataWrite funtion to display.

I/P Arguments: String(Address of the string) to be displayed.
Return value : None

void LCD_DisplayString(char *string_ptr)
{
   while(*string_ptr)
    LCD_DataWrite(*string_ptr++);
 }

LCD_DisplayNumber()

Description :This function is used to display a 5-digit integer(0-65535).
- ex:

if the number is 12345 then 12345 is displayed.
if the number is 123 then 00123 is displayed.

Function name: LCD_DisplayNumber()
I/P Arguments: unsigned int.
Return value : none

void LCD_DisplayNumber(unsigned int num)
{
   LCD_DataWrite((num/10000)+0x30);
   num=num%10000;
 
   LCD_DataWrite((num/1000)+0x30);
   num=num%1000;
 
   LCD_DataWrite((num/100)+0x30);
   num=num%100;
 
   LCD_DataWrite((num/10)+0x30);
 
   LCD_DataWrite((num%10)+0x30);
 
 }

LCD_ScrollMessage()

Description :This function scrolls the given message on the first line.""

16 chars are displayed at atime.
Pointer is incremented to skip a char each time to give the illusion of moving chars.
If the chars are less than 16, then the BlankSpaces are displayed.

I/P Arguments: char *msg_ptr

(msg_ptr -> pointer to the string to be scrolled)

Return value : none

void LCD_ScrollMessage(char *msg_ptr)
{
  unsigned char i,j;
  LCD_CmdWrite(0x0c);			 //Disable the Cursor
  for(i=0;msg_ptr[i];i++)        //Loop to display the complete string
    {                            //each time 16 chars are displayed and
                                 //pointer is incremented to point to next char
 
      LCD_GoToLineOne();                   //Move the Cursor to first line
 
      for(j=0;j<LCDMaxChars && msg_ptr[i+j];j++) //loop to Display first 16 Chars
	    LCD_DataWrite(msg_ptr[i+j]);                 //or till Null char
 
	  for(j=j; j<LCDMaxChars; j++)               //If the chars are below 16
        LCD_DataWrite(BlankSpace);              //then display blank spaces
 
       _delay_ms(500);
    }
   LCD_CmdWrite(0x0E);			  //Enable the Cursor
}

LCD_DisplayRtcTime()

Description :This function display hour,min,sec read from DS1307.
I/P Arguments: char hour,char min,char sec(hour,min,sec should be packed BCD format,as read from DS1307)
Return value : none

void LCD_DisplayRtcTime(char hour,char min,char sec)
{
    LCD_DataWrite(((hour>>4) & 0x0f) + 0x30);
    LCD_DataWrite((hour & 0x0f) + 0x30);
    LCD_DataWrite(':');
 
    LCD_DataWrite(((min>>4) & 0x0f) + 0x30);
	LCD_DataWrite((min & 0x0f) + 0x30);
    LCD_DataWrite(':');
 
    LCD_DataWrite(((sec>>4) & 0x0f) + 0x30);
	LCD_DataWrite((sec & 0x0f) + 0x30);
 
 }

LCD_DisplayRtcDate()

Description :This function display day,month,year read from DS1307.
I/P Arguments: char day,char month,char year(day,month,year should be packed BCD format,as read from DS1307)
Return value : none

void LCD_DisplayRtcDate(char day,char month,char year)
 {
     LCD_DataWrite(((day>>4) & 0x0f) + 0x30);
     LCD_DataWrite((day & 0x0f) + 0x30);
     LCD_DataWrite('/');
 
     LCD_DataWrite(((month>>4) & 0x0f) + 0x30);
 	 LCD_DataWrite((month & 0x0f) + 0x30);
     LCD_DataWrite('/');
 
     LCD_DataWrite(((year>>4) & 0x0f) + 0x30);
 	LCD_DataWrite((year & 0x0f) + 0x30);
 
 }

LCD_4_bit Mode

                       AVR LCD library for 4-bit mode

Filename: lcd_4_bit.c
Controller: Atmega Family(8,16,32,64,128)
Oscillator: 11.0592 MHz
Author: XploreLabz
website: www.xplorelabz.com

Note:

Pin connection for LCD display in 4-bit mode.
By default the LCD is connected to PORTB.
The code can be modified to connect the LCD to any of the PORTs by changing the "#define databus PORTB".

io.h contains the defnition of all ports and SFRs delay.h contains the in built delay routines(us and ms routines)

#include <avr\io.h>
#include <util\delay.h>
 
#include "lcd.h"
 
#define databus_direction DDRB //  LCD data and Control bus Direction Configuration
 
#define databus	PORTB      //	LCD databus connected to PORTB
#define control_bus PORTB      //	LCD Control bus connected to PORTB
 
#define rs 0                // Register select pin connected 1st bit(D0) Control bus
#define rw 1                // Read Write pin connected to 2nd bit(D1) Control bus
#define en 2                // Enable pin connected to 3rd bit(D2) Control bus
 
 
/* 16x2 LCD Specification */
#define LCDMaxLines 2
#define LCDMaxChars 16
#define LineOne 0x80
#define LineTwo 0xc0
 
#define BlankSpace ' '

LCD_Init()

Description :This function is used to initialize the lcd in 4-bit mode
Function name: LCD_Init()
I/P Arguments: none
Return value : none

void LCD_Init()
{
   _delay_ms(50);
   databus_direction = 0xff;  // Configure both databus and controlbus as output
   LCD_CmdWrite(0x02);	       //Initilize the LCD in 4bit Mode
   LCD_CmdWrite(0x28);
   LCD_CmdWrite(0x0E);	      // Display ON cursor ON
   LCD_CmdWrite(0x01);	      // Clear the LCD
   LCD_CmdWrite(0x80);	      // Move the Cursor to First line First Position
 
}

LCD_CmdWrite()

Description :This function sends a command to LCD in the following steps.
- step1: Send the Higher Nibble of the I/P command to LCD.
- step2: Select the Control Register by making RS low.
- step3: Select Write operation making RW low.
- step4: Send a High-to-Low pulse on Enable PIN with some delay_us.
- step5: Send the Lower Nibble of the I/P command to LCD.
- step6: Select the Control Register by making RS low.
- step7: Select Write operation making RW low.
- step8: Send a High-to-Low pulse on Enable PIN with some delay_us.
I/P Arguments: 8-bit command supported by LCD.
Return value : none

void LCD_CmdWrite( char cmd)
{
 
    databus=(cmd & 0xf0);        // Send the Higher Nibble of the command to LCD
    control_bus &=~(1<<rs);  // Select the Command Register by pulling RS LOW
    control_bus &=~(1<<rw);  // Select the Write Operation  by pulling RW LOW
    control_bus |=1<<en;     // Send a High-to-Low Pusle at Enable Pin
	_delay_us(1);
    control_bus &=~(1<<en);
 
    _delay_us(10);				// wait for some time
 
   databus=((cmd<<4) & 0xf0);   // Send the Lower Nibble of the command to LCD
    control_bus &=~(1<<rs);  // Select the Command Register by pulling RS LOW
    control_bus &=~(1<<rw);  // Select the Write Operation  by pulling RW LOW
    control_bus |=1<<en;     // Send a High-to-Low Pusle at Enable Pin
	_delay_us(1);
    control_bus &=~(1<<en);
 
   _delay_ms(1);
}

LCD_DataWrite()

Description:This function sends a character to be displayed on LCD in the following steps.
- step1: Send the higher nibble of the character to LCD.
- step2: Select the Data Register by making RS high.
- step3: Select Write operation making RW low.
- step4: Send a High-to-Low pulse on Enable PIN with some delay_us.
- step5: wait for some time
- step6: Send the lower nibble of the character to LCD.
- step7: Select the Data Register by making RS high.
- step8: Select Write operation making RW low.
- step9: Send a High-to-Low pulse on Enable PIN with some delay_us.
Function name: LCD_DataWrite()
I/P Arguments: ASCII value of the char to be displayed.
Return value : none

void LCD_DataWrite( char dat)
{
    databus=(dat & 0xf0);	  // Send the Higher Nibble of the Data to LCD
    control_bus |=1<<rs;	  // Select the Data Register by pulling RS HIGH
    control_bus &=~(1<<rw);	  // Select the Write Operation  by pulling RW LOW
    control_bus |=1<<en;	  // Send a High-to-Low Pusle at Enable Pin
	_delay_us(1);
    control_bus &=~(1<<en);
    _delay_us(10);
 
   databus=((dat <<4) & 0xf0); // Send the Lower Nibble of the Data to LCD
    control_bus |=1<<rs;	   // Select the Data Register by pulling RS HIGH
    control_bus &=~(1<<rw);	   // Select the Write Operation  by pulling RW LOW
    control_bus |=1<<en;	   // Send a High-to-Low Pusle at Enable Pin
	_delay_us(1);
    control_bus &=~(1<<en);
    _delay_ms(1);
 
}

Keypad

                       Avr 4x4 Keypad Library

Filename: keypad.c
Controller:Atmega8/16/32/128
Oscillator: 11.0592 MHz
Author: XploreLabz
website: www.xplorelabz.com

Note:

Rows are connected to lower 4-bits of PORTC
Cols are connected to higher 4-bits of PORTC

#include <avr\io.h>
#include <util\delay.h>
#include "keypad.h"
#include "lcd.h"
#define RowColDirection DDRB //Data Direction Configuration for keypad
#define ROW PORTB            //Lower four bits of PORTC are used as ROWs
#define COL PINB            //Higher four bits of PORTC are used as COLs

KEYPAD_Init()

Description : This function the rows and colums for keypad scan

ROW lines are configured as Output.
Column Lines are configured as Input.

I/P Arguments:none
Return value : none

void KEYPAD_Init()
{
       RowColDirection=0xf0;   // Configure Row lines as O/P and Column lines as I/P
}

KEYPAD_WaitForKeyRelease()

Description : This function waits till the previous key is released.

All the ROW lines are pulled low.
Column Lines are read to check the key press.
If all the Keys are released then Column lines will remain high(0x0f)

I/P Arguments:none
Return value : none

void KEYPAD_WaitForKeyRelease()
{
   unsigned char key;
    do
	{
          ROW=0x0f;         // Pull the ROW lines to low and Column high low.
	    key=COL & 0x0f;   // Read the Columns, to check the key press
       }while(key!=0x0f);   // Wait till the Key is released,
                            // If no Key is pressed, Column lines will remain high (0x0f)
}

KEYPAD_WaitForKeyPress()

Description : This function waits till a new key is pressed.

All the ROW lines are pulled low.
Column Lines are read to check the key press.
If any Key is pressed then corresponding Column Line goes low.
Wait for Some time and perform the above operation to ensure the True Key Press before decoding the KEY.

I/P Arguments:none
Return value : none

void KEYPAD_WaitForKeyPress()
{
  unsigned char key;
  do
   {
	 do
      {
	   ROW=0x0f;	   // Pull the ROW lines to low and Column lines high.
	   key=COL & 0x0F;   // Read the Columns, to check the key press
	  }while(key==0x0f); // Wait till the Key is pressed,
			         // if a Key is pressed the corresponding Column line go low
 
	   _delay_ms(1);		  // Wait for some time(debounce Time);
 
	   ROW=0x0f;		  // After debounce time, perform the above operation
	   key=COL & 0x0F;	  // to ensure the Key press.
 
	}while(key==0x0f);
 
 }

KEYPAD_ScanKey()

Description : This function scans all the rows to decode the key pressed.

Each time a ROW line is pulled low to detect the KEY.
Column Lines are read to check the key press.
If any Key is pressed then corresponding Column Line goes low.
Return the ScanCode(Combination of ROW & COL) for decoding the key.

I/P Arguments:none
Return value : char--> Scancode of the Key Pressed

unsigned char KEYPAD_ScanKey()
 {
 
	 unsigned char ScanKey = 0xe0,i, key;
 
  for(i=0;i<0x04;i++)           // Scan All the 4-Rows for key press
    {
      ROW=ScanKey + 0x0F;         // Select 1-Row at a time for Scanning the Key
      key=COL & 0x0F;             // Read the Column, for key press
 
      if(key!= 0x0F)             // If the KEY press is detected for the selected
         break;                   // ROW then stop Scanning,
 
     ScanKey=(ScanKey<<1)+ 0x10; // Rotate the ScanKey to SCAN the remaining Rows
    }
 
    key = key + (ScanKey & 0xf0);  // Return the row and COL status to decode the key
 
    return(key);
}

KEYPAD_GetKey()

Description: This function waits till a key is pressed and returns its ASCII Value

Wait till the previous key is released..
Wait for the new key press.
Scan all the rows one at a time for the pressed key.
Decode the key pressed depending on ROW-COL combination and returns its ASCII value.

I/P Arguments: none
Return value : char--> ASCII value of the Key Pressed

unsigned char KEYPAD_GetKey()
{
	unsigned char key;
 
      KEYPAD_WaitForKeyRelease();    // Wait for the previous key release
      _delay_ms(1);
 
      KEYPAD_WaitForKeyPress();      // Wait for the new key press
      key = KEYPAD_ScanKey();        // Scan for the key pressed.
 
   switch(key)                       // Decode the key
     {
        case 0xe7: key='0'; break;
        case 0xeb: key='1'; break;
        case 0xed: key='2'; break;
        case 0xee: key='3'; break;
        case 0xd7: key='4'; break;
        case 0xdb: key='5'; break;
        case 0xdd: key='6'; break;
        case 0xde: key='7'; break;
        case 0xb7: key='8'; break;
        case 0xbb: key='9'; break;
        case 0xbd: key='A'; break;
        case 0xbe: key='B'; break;
        case 0x77: key='C'; break;
        case 0x7b: key='D'; break;
        case 0x7d: key='E'; break;
        case 0x7e: key='F'; break;
       default: key='z';
      }
   return(key);                      // Return the key
}

UART

  AVR UART library for Serial Communication for 9600 baud rate at 11.0592Mhz

Filename: uart.c
Controller: Atmega8/16/32/128
Oscillator: 11.0592 MHz
Author: XploreLabz
website: www.xplorelabz.com

  #include<avr/io.h>

UART_Init()

Description :This function is used to initialize the UART at 9600 baud rate by below configuration.
I/P Arguments: none
Return value : none

void UART_Init()
{
        UCSRB= 0x18;   // Enable Receiver and Transmitter
        UCSRC= 0x86;   // Asynchronous mode 8-bit data and 1-stop bit
        UCSRA= 0x00;   // Normal Baud rate(no doubling), Single processor commn
        UBRRH= 0;
        UBRRL= 71;     // 9600 Baud rate at 11.0592MHz
  }

UART_RxChar()

Description :This function is used to receive a char from UART module.

It waits till a char is received ie.till RXC is set,
RXC will be set once a CHAR is received.
Finally returns the received char.

I/P Arguments: none
Return value : char

char UART_RxChar()
{
   while((UCSRA & (1<<RXC))==0);   // Wait till the data is received
    return(UDR);                    // return the received char
}

UART_TxChar()

Description :This function is used to transmit a char through UART module.

It waits till previous char is transmitted ie.till UDRE is set.
UDRE will be set once a CHAR is transmitted ie UDR becomes empty.
Finally the new Char to be transmitted is loaded into UDR.

I/P Arguments: char--> data to be transmitted
Return value : none

 
 void UART_TxChar(char ch)
{
   while((UCSRA & (1<<UDRE))==0); // Wait till Transmitter(UDR) register becomes Empty
              UDR =ch;             // Load the data to be transmitted
}

UART_TxString()

Description :This function is used to transmit the ASCII string through UART.

The string_ptr points to the first char of the string.
And it is incremented each time to traverse till the end(NULL CHAR).
Each time a char is sent to UART_TxChar() fun to transmit it through UART

I/P Arguments: String(Address of the string) to be transmitted.
Return value : none

 
 
void UART_TxString(char *string_ptr)
 {
          while(*string_ptr)
           UART_TxChar(*string_ptr++);
   }

UART_RxString()

Description :

This function is used to receive a ASCII string through UART till the carriage_return/New_line.
The string_ptr points to the begining of the string and each time UART_RxChar() function is called to receive a char and copy it into the buffer(STRING) and incrment string_ptr.
Once the carriage_return/New_line is encountered the loop is breaked and the String is NULL terminated.

I/P Arguments: *string_ptr
(Address of the string where the received data needs to be stored)
Return value : none

NOTE:

The received char is ECHOED back,if not required then comment UART_TxChar(ch) in the code.
BackSlash is not taken care.

void UART_RxString(char *string_ptr)
 {
     char ch;
     while(1)
       {
          ch=UART_RxChar();    //Reaceive a char
          UART_TxChar(ch);     //Echo back the received char
 
         if((ch=='\r') || (ch=='\n')) //read till enter key is pressed
           {                          //once enter key is pressed
              *string_ptr=0;          //null terminate the string
                break;                //and break the loop
             }
         *string_ptr=ch;              //copy the char into string.
         string_ptr++;                //and increment the pointer
      }
 }

UART_TxNumber()

Description :This function is used to transmit a 5-digit integer(0-65535).
- ex:

if the number is 12345 then 12345 is transmitted.
if the number is 123 then 00123 is transmitted.

I/P Arguments: unsigned int
Return value : none

void UART_TxNumber(unsigned int num)
{
 
       UART_TxChar((num/10000)+0x30);
       num=num%10000;
 
       UART_TxChar((num/1000)+0x30);
       num=num%1000;
 
       UART_TxChar((num/100)+0x30);
       num=num%100;
 
       UART_TxChar((num/10)+0x30);
 
       UART_TxChar((num%10)+0x30);
}

@@ Line 810: / Line 810: @@
 </syntaxhighlight>
@@ Line 820: / Line 818: @@
 #''Once the carriage_return/New_line is encountered the loop is breaked and the String is NULL terminated.''
 *''I/P Arguments: *string_ptr''
-     ''(Address of the string where the received data needs to be stored)''
+*''(Address of the string where the received data needs to be stored)''
 *''Return value : none''
@@ Line 847: / Line 845: @@
   }
 </syntaxhighlight>

Difference between revisions of "AVR C Library"

Revision as of 20:12, 22 October 2013

Contents

Introduction

Overview:

Reference:

Feedback:

Disclaimer:

ADC

ADC_Init()

ADC_StartConversion()

LCD_8_bit Mode

LCD_Init()

LCD_Clear()

LCD_GoToLineOne()

LCD_GoToLineTwo()

LCD_GoToXY()

LCD_CmdWrite()

LCD_DataWrite()

LCD_DisplayString()

LCD_DisplayNumber()

LCD_ScrollMessage()

LCD_DisplayRtcTime()

LCD_DisplayRtcDate()

LCD_4_bit Mode

LCD_Init()

LCD_CmdWrite()

LCD_DataWrite()

Keypad

KEYPAD_Init()

KEYPAD_WaitForKeyRelease()

KEYPAD_WaitForKeyPress()

KEYPAD_ScanKey()

KEYPAD_GetKey()

UART

UART_Init()

UART_RxChar()

UART_TxChar()

UART_TxString()

UART_RxString()

UART_TxNumber()