LPC2148 Timers Revision as of 14:54, 20 July 2016 by Explorer (Talk | contribs) (diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)

In this tutorial, we are going to discuss the Timer module of LPC2148 . First, we will see how to configure the Timer0 and Timer1 registers to generate a delay of 100ms and 500ms respectively. At the end, we will see how to use the ExploreEmdedded Timer library.

LPC2148 Timer Module

LPC1768 has four 32-bit independent timers (Timer0-Timer3). Each timer has a 32-bit pre-scalar to generate wide range of delays. Each timer has 4 match registers with which 4 different delays can be generated using a single timer.

LPC2148 Timer Registers

The below table shows the registers associated with LPC2148 Timer module.

Register	Description
IR	Interrupt Register: The IR can be read to identify which of 6(4-match, 2-Capture) possible interrupt sources are pending. Writing Logic-1 will clear the corresponding interrupt.
TCR	Timer Control Register: The TCR is used to control the Timer Counter functions(enable/disable/reset).
TC	Timer Counter: The 32-bit TC is incremented every PR+1 cycles of PCLK. The TC is controlled through the TCR.
PR	Prescaler Register: This is used to specify the Prescaler value for incrementing the TC.
PC	Prescale Counter: The 32-bit PC is a counter which is incremented to the value stored in PR. When the value in PR is reached, the TC is incremented.
MCR	Match Control Register: The MCR is used to control the resetting of TC and generating of interrupt whenever a Match occurs.
MR0-MR3	Match Registers: The Match register values are continuously compared to the Timer Counter value. When the two values are equal, actions can be triggered automatically. The action possibilities are to generate an interrupt, reset the Timer Counter, or stop the timer. Actions are controlled by the settings in the MCR register.

Register Configuration

TCR
31:2	1	0
Reserved	Counter Reset	Counter Enable

Bit 0 – Counter Enable
This bit is used to Enable or Disable the Timer Counter and Prescalar Counter
0- Disable the Counters
1- Enable the Counter incrementing.

Bit 1 – Counter reset
This bit is used to clear the Timer counter and PWM Prescalar Counter values.
0- Do not Clear.
1- The Timer Counter and the Prescaler Counter are synchronously reset on the next positive edge of PCLK.

MCR
31:21	11	10	9	8	7	6	5	4	3	2	1	0
Reserved	MR3S	MR3R	MR3I	MR2S	MR2R	MR2I	MR1S	MR1R	MR1I	MR0S	MR0R	MR0I

MRxI
This bit is used to Enable or Disable the Timer interrupts when the TC matches MRx (x:0-3)
0- Disable the Timer Match interrupt
1- Enable the Timer Match interrupt.

MRxR
This bit is used to Reset TC whenever it Matches MRx(x:0-3)
0- Do not Clear.
1- Reset TC counter value whenever it matches MRx.

MRxS
This bit is used to Stop TC and PC whenever the TC matches MRx(x:0-3).
0- Disable the Timer stop on match feature
1- Enable the Timer Stop feature. This will stop the Timer whenever the TC reaches the Match register value.

Prescalar Calculation

Timer delay generated by the LPC1768 depends on the input clock and the pre-scalar values. The required pre-scalar value can be determined by the pclk (peripheral clock). PCLKSEL0 and PCLKSEL1 register have the PCLK info for all the 4 timers.

Timer	PCLKSELx	Bits	Symbol	Description
Timer0	PCLKSEL0	3-2	PCLK_TIMER0	Peripheral clock selection for TIMER0.
Timer1	PCLKSEL0	5-4	PCLK_TIMER1	Peripheral clock selection for TIMER1.
Timer2	PCLKSEL1	13-12	PCLK_TIMER2	Peripheral clock selection for TIMER2.
Timer3	PCLKSEL1	15-14	PCLK_TIMER3	Peripheral clock selection for TIMER3.

Getting the PCLK value.
Using the 2-bit information from PCLKSELx registers the pclk can be determined as below..

PCLKSELx bits	PCLK
0	SystemCoreClock/4
1	SystemCoreClock
2	SystemCoreClock/2
3	SystemCoreClock/8

Calculating the Pre-scalar value.
After getting the pclk value the prescalar count for 1us delay can be calculated as below.

Steps to Configure Timer

1. Power On the Timer module by setting the appropriate bits in PCONP register.
2. Configure MCR to reset the TC and generate the interrupt whenever it matches MRx.
3. Set the pre-scalar value for 1us.
4. Update the MRx register with required delay in micro secs.
5. Configure TCR to enable the Counter for incrementing the TC.
6. Enable the required timer interrupt.
7. Configure the GPIO pins as output for blinking the LEDs.
8. Toggle the LEDs in ISR whenever the interrupt is generated.

Example

Program to demonstrates the led blinking with 100ms and 500ms delay using the timer interrupts

Using ExploreEmbedded Libraries

In the above tutorial we just discussed how to configure and use the Timer module of LPC1768 to generate 100ms and 500ms delay
Once you know the internals of LPC7168 Timers, you can directly use the ExploreEmbedded libraries to generate the required Delays.
The below sample code shows how to use the ExploreEmbedded Timer library.

Timer Delay measured using CRO.

Downloads

Download the complete project folder from the below link:

Have an opinion, suggestion , question or feedback about the article let it out here!