---
Contents
Objective
In this tutorial we will be discussing about the internal RTC of LPC1768. We will see what are the different registers associated with the RTC but we will mainly focus on basics registers required to use RTC. Later we will see how to use Explore Embedded library for RTC.
RTC Registers
RTC Registers | ||||||||
---|---|---|---|---|---|---|---|---|
Register | Description | |||||||
CCR | Clock Control Register | |||||||
Consolidated Time Registers | ||||||||
CTIME 0 | Consolidated Time Register 0 | |||||||
CTIME 1 | Consolidated Time Register 1 | |||||||
CTIME 2 | Consolidated Time Register 2 | |||||||
Time Counter Registers | ||||||||
SEC | Seconds Counter | |||||||
MIN | Minutes Register | |||||||
HOUR | Hours Register | |||||||
DOM | Day of Month Register | |||||||
DOW | Day of Week Register | |||||||
DOY | Day of Year Register | |||||||
MONTH | Months Register | |||||||
YEAR | Years Register | |||||||
CALIBRATION | Calibration value Register |
RTC Register Configuration
CCR ( Clock Control Register )
CCR | ||||||||
---|---|---|---|---|---|---|---|---|
31:5 | 4 | 3:2 | 1 | 0 | ||||
- | CCALEN | - | CTCRST | CLKEN |
Bit 0 – CLKEN : Clock Enable
This bit is written with one to enable time counters and written with zero to disable time counters.
Bit 1 - CTCRST : CTC Reset
Bit 3:2
These bits must be set to zero for normal RTC operation.
Bit 4 - CCALEN : Calibration counter enable
To disable calibration counter and reset it to zero, write one to this bit.
When written zero, the counter is enabled and starts counting
Bit 31:5 Reserved
Time Counter Register
The time value consists of the eight counters and there is one register associated with each counter. To update the RTC, new values should be written to these registers.
Time Counter Register | ||||||||
---|---|---|---|---|---|---|---|---|
Register | Description | Minimum Value | Maximum Value | |||||
SEC | Seconds value | 0 | 59 | |||||
MIN | Minutes value | 0 | 59 | |||||
HOUR | Hours value | 0 | 23 | |||||
DOM | Day of Month value | 1 | 28,29,30 or 31 ( depending on the month and whether it is a leap year) | |||||
DOW | Day of Week value | 0 | 6 | |||||
DOY | Day of Year value | 1 | 365 (366 for Leap Year) | |||||
MONTH | Month value | 1 | 12 | |||||
YEAR | Year value | 0 | 4095 |
Consolidated Time Registers
The values of the Time Counters can optionally be read in a consolidated format which allows the programmer to read all time counters with only three read operations.
There are 3 Consolidated Time Registers. The minimum and maximum values of the various fields in these registers are same as the respective Time Counter Register.
These registers are read only. New values should be written to Time Counter Registers.
Consolidated Time Register 0 (CTIME0)
CTIME0 | ||||||||
---|---|---|---|---|---|---|---|---|
31:27 | 26:24 | 23:21 | 20:16 | 15:14 | 13:8 | 7:6 | 5:0 | |
Reserved | Day of Week | Reserved | Hours | Reserved | Minute | Reserved | Second |
Consolidated Time Register 1 (CTIME1)
CTIME1 | ||||||||
---|---|---|---|---|---|---|---|---|
31:27 | 27:16 | 15:12 | 11:8 | 7:5 | 4:0 | |||
Reserved | Year | Reserved | Month | Reserved | Day of Month |
Consolidated Time Register 2 (CTIME2)
CTIME2 | ||||||||
---|---|---|---|---|---|---|---|---|
31:12 | 11:0 | |||||||
Reserved | Day of Year |
Steps for Configuring RTC
Code EXample
Example 1
Using Explore Embedded Liberaries