Difference between revisions of "Starter SST89E516RD USB Development board"
| (6 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
[[Category:8051 Development Boards]] | [[Category:8051 Development Boards]] | ||
| + | [[File:Cart add.png|right|link=https://www.exploreembedded.com/product/Starter%20SST89E516RD%20USB%20Development%20board]] | ||
{{Popup|type=l|text= ''This is latest 8051 Starter Development board from Explore Embedded, the board uses '''SST89E512RD''' Microcontroller which is '''100%''' compatible with '''P89V51RD2'''. The board has USB to Serial Convertor which can be used to program/flash the MCU; eliminates need for a programmer. It can used with laptops as well!''}} | {{Popup|type=l|text= ''This is latest 8051 Starter Development board from Explore Embedded, the board uses '''SST89E512RD''' Microcontroller which is '''100%''' compatible with '''P89V51RD2'''. The board has USB to Serial Convertor which can be used to program/flash the MCU; eliminates need for a programmer. It can used with laptops as well!''}} | ||
| + | [[File:DSC09000.JPG|x480px]] | ||
| + | <gallery mode="packed"> | ||
| + | File:DSC09010.JPG | ||
| + | File:DSC09023.JPG | ||
| + | File:DSC01041.JPG | ||
| + | </gallery> | ||
{{Box|type=l_green_light|text = '''Features'''}} | {{Box|type=l_green_light|text = '''Features'''}} | ||
{{Box|type=l_green_light|text = <br/> | {{Box|type=l_green_light|text = <br/> | ||
| Line 46: | Line 53: | ||
*[http://exploreembedded.com/wiki/images/c/cb/EasyIAP_Rev_6.0.zip Download EasyIAP] and install it. | *[http://exploreembedded.com/wiki/images/c/cb/EasyIAP_Rev_6.0.zip Download EasyIAP] and install it. | ||
*Follow the steps in the pictures below to detect the board and flash the hex file | *Follow the steps in the pictures below to detect the board and flash the hex file | ||
| + | }} | ||
| + | [[File:7 Flash.JPG|framed|x400px|Follow steps in images below:]] | ||
<gallery> | <gallery> | ||
| − | File:0_device manager. | + | File:0_device manager.JPG |
| − | File:1_Install SW. | + | File:1_Install SW.JPG |
| − | File:3_setup. | + | File:3_setup.JPG |
| − | File:4_connect. | + | File:4_connect.JPG |
| − | File:5_Browse. | + | File:5_Browse.JPG |
| − | File:6_OK. | + | File:6_OK.JPG |
| − | File: | + | File:7 Flash.JPG |
</gallery> | </gallery> | ||
| − | + | =8051 Video Tutorials= | |
| − | }} | + | And that's not all watch this complete series of 8051 video tutorials, which we believe should definitely help you build |
| + | {{#widget:YouTube|playlist=PLRuRKN7_FVgtdXWWM-uosWYfmOFDp63dd|width=680}} | ||
| + | {{DISQUS}} | ||
Latest revision as of 18:41, 6 March 2015
This is latest 8051 Starter Development board from Explore Embedded, the board uses SST89E512RD Microcontroller which is 100% compatible with P89V51RD2. The board has USB to Serial Convertor which can be used to program/flash the MCU; eliminates need for a programmer. It can used with laptops as well!
Features
- SST89E516RD Microcontroller with bootloader (no programmer needed)
- CP2102 USB to Serial Convertor on board
- 16 x 2 LCD Interface
- Switches x2
- LEDs x2
- All Ports pins as breakout.
- High quality FR4 , wave soldered PCB.
SST89E516RD MCU Features
- 1 KByte Internal RAM
- Dual Block SuperFlash EEPROM– 64 KByte primary block +8 KByte secondary block
- Support External Address Range up to 64KByte of Program and Data Memory
- Three High-Current Drive Ports (16 mA each)
- Three 16-bit Timers/Counters
- Full-Duplex, Enhanced UART– Framing Error Detection– Automatic Address Recognition
- Ten Interrupt Sources at 4 Priority Levels– Four External Interrupt Inputs
- Programmable Watchdog Timer (WDT)
- Programmable Counter Array (PCA)
- Four 8-bit I/O Ports (32 I/O Pins) andOne 4-bit Port
- Second DPTR register
- Low EMI Mode (Inhibit ALE)
- SPI Serial Interface
- Standard 12 Clocks per cycle, the device has adoption to double the speed to 6 clocks per cycle.
- TTL- and CMOS-Compatible Logic Levels
- Brown-out Detection
- Low Power Modes– Power-down Mode with External Interrupt Wake-up– Idle Mode
Downloads
Setting up EasyIAP SW and programming the hex file
- Connect the Board to the computer and install Windows USB to UART Drivers for CP2102.
- Note: Power up the board with 7 to 12V, 1A adapter, the board does not power up from USB.
- Note down the COM Port Number e.g. COM 2 from device manager
- Download EasyIAP and install it.
- Follow the steps in the pictures below to detect the board and flash the hex file
Follow steps in images below:
8051 Video Tutorials
And that's not all watch this complete series of 8051 video tutorials, which we believe should definitely help you build {{#widget:YouTube|playlist=PLRuRKN7_FVgtdXWWM-uosWYfmOFDp63dd|width=680}}