Revision as of 13:52, 21 March 2016

Basics

Timers come in handy when you want to set some time interval like your alarm. This can be very precise to a few microseconds. Timers/Counters are essential part of any modern MCU. Remember it is the same hardware unit inside the MCU that is used either as Timers or Counter. Timers/counters are an independent unit inside a micro-controller. They basically run independently of what task CPU is performing. Hence they come in very handy, and are primarily used for the following:

Internal Timer: As an internal timer the unit, ticks on the oscillator frequency. The oscillator frequency can be directly feed to the timer or it can be pre-scaled. In this mode it used generate precise delays. Or as precise time counting machine.
External Counter: In this mode the unit is used to count events on a specific external pin on a MCU.
Pulse width Modulation(PWM) Generator: PWM is used in speed control of motors and various other applications.

Atmega32 has 3 timer units, timer 0, timer 1 and timer 2 respectively. Let us start our exploration with timer 0.

Timer 0 Basics

Timer 0 is a 8 bit timer. It basically means it can count from 0 to 2^8 255. The operation of timer 0 is straight forward. The TCNT0 register hold the timer Count and it is incremented on every timer "tick". If the timer is turned on it ticks from 0 to 255 and overflows. If it does so, a Timer OverFlow Flag(TOV) is set.

You can as well load a count value in TCNT0 and start the timer from a specific count. Another interesting feature is that a value can be set in the Output Compare Register (OCR0), and whenever TCNT0 reaches that value, the Output Compare Flag (OCF0) flag is Set.

Timer/Counter 0
TCNT0
D7	D6	D5	D4	D3	D2	D1	D0

The configuration of the Timer can be set using the TCCR0 register shown below. With this you can basically select two things:

The Frequency of the Clock Source with CS02, CS01, CS00 bits.
The mode of the timer. For the first example we will use it in normal mode where it ticks from zero to the highest value(255)

Timer Counter Control Register 0
TCCR0
D7	D6	D5	D4	D3	D2	D1	D0
FOC0	WGM00	COM01	COM00	WGM01	CS02	CS01	CS00

D2	D1	D0	Clock Source
CS02	CS01	CS00	Freq
0	0	0	No Clock (Stopped)
0	0	1	Clk
0	1	0	Clk/8
0	1	1	Clk/64
1	0	0	Clk/256
1	0	1	Clk/1024
1	1	0	Clk/T0-Falling edge
1	1	1	Clk/T0-Rising Edge

D6	D3	PWM
WGM00	WGM01	Mode
0	0	Normal
0	1	CTC (Clear timer on compare match)
1	0	PWM (Phase correct)
1	1	Fast PWM

The Timer/counter Interrupt Flag Register(TIFR) holds the two basic flags we need the TOV and OVF. Other bits correspond to the timer interrupts, which we will look at in another tutorial.

Timer/Counter 0 Flag Register
TIFR
D7	D6	D5	D4	D3	D2	D1	D0
OCF2	TOV2	ICF1	OCF1A	OCF1B	TOV1	OCF0	TOV0

Timer 0 Example

Let us do a simple example to set the timer 0 in normal mode and toggle an LED when it overflows. To accomplish this, we'll do the following steps.

Load TCNT0 with 0x00

Timer 1

Timer 2

@@ Line 9: / Line 9: @@
 Atmega32 has 3 timer units, timer 0, timer 1 and timer 2 respectively. Let us start our exploration with timer 0.
-=Timer 0 =
+=Timer 0 Basics =
 [[File:Timer 0.png|center]]
 Timer 0 is a 8 bit timer. It basically means it can count from 0 to 2^8 255. The operation of timer 0 is straight forward. The TCNT0 register hold the timer Count and it is incremented on every timer '''"tick"'''. If the timer is turned on it ticks from 0 to 255 and overflows.  If it does so, a Timer OverFlow Flag(TOV) is set.
@@ Line 81: / Line 81: @@
 |OCF2||TOV2||ICF1||OCF1A||OCF1B||TOV1||OCF0||TOV0
 |}
+=Timer 0 Example=
+Let us do a simple example to set the timer 0 in normal mode and toggle an LED when it overflows. To accomplish this, we'll do the following steps.
+# Load TCNT0 with 0x00
+#
 =Timer 1=
 =Timer 2=

Difference between revisions of "AVR Timer programming"