Line 48: Line 48:
 
TRISD = (1<<0) | (1<3) | (1<<6); // Configure PD0,PD3,PD6 as Input and others as Output
 
TRISD = (1<<0) | (1<3) | (1<<6); // Configure PD0,PD3,PD6 as Input and others as Output
 
</syntaxhighlight>   
 
</syntaxhighlight>   
<br>
+
<br><br>
  
 
<b>PORTx:</b><br>
 
<b>PORTx:</b><br>
 
This register is used to read/write the data from/to port pins. Writing 1's to PORTx will make the corresponding PORTx pins as HIGH. Similarly writing 0's to PORTx will make the corresponding PORTx pins as LOW.<br>
 
This register is used to read/write the data from/to port pins. Writing 1's to PORTx will make the corresponding PORTx pins as HIGH. Similarly writing 0's to PORTx will make the corresponding PORTx pins as LOW.<br>
<b>Before reading/writing the data the port pins should be configured as InputOutput</b>.
+
<b>Before reading/writing the data, the port pins should be configured as InputOutput</b>.
 
<syntaxhighlight>
 
<syntaxhighlight>
 
PORTB = 0xff;  // Make all PORTB pins HIGH.
 
PORTB = 0xff;  // Make all PORTB pins HIGH.
Line 63: Line 63:
  
  
TRISB = 0x00;  // Configure PORTB as Input
+
TRISB = 0x00;  // Configure PORTB as Output
TRISD = 0xff;  // Configure PORTD as Output
+
TRISD = 0xff;  // Configure PORTD as Input
 
PORTD = PORTB; // Read the data from PORTB and send it to PORTD.
 
PORTD = PORTB; // Read the data from PORTB and send it to PORTD.
 
</syntaxhighlight>
 
</syntaxhighlight>
 +
<br><br>
  
 
=Led Blinking Example=
 
=Led Blinking Example=

Revision as of 18:24, 3 May 2016

In this tutorial we are going to discuss the port configuration of PIC controllers. In this tutorial we will be using PIC16F877A as reference, same will be applicable to other PIC series controllers.
At the end of this tutorial you will be familiar with the PIC GPIO's and the associated registers for configuring and accessing the GPIO's.

GPIO Registers

The basic and important feature of any controllers is the number of gpio's available for connecting the peripherals. PIC16F877A has 33-gpio's grouped into five ports namely PORTA-PORTE as shown in the below table.

PORT Direction Register Number of Pins Alternative Function
PORTA TRISA 6 (PA0-PA5) ADC
PORTB TRISB 8 (PB0-PB7) Interrupts
PORTC TRISC 8 (PC0-PC7) UART,I2C,PWM
PORTD TRISD 8 (PD0-PD7) Parallel Slave Port
PORTE TRISE 3 (PE0-PB2) ADC

As shown in the above table many I/O pins have 2-3 functions. If a pin is used for other function then it may not be used as a gpio.

Though the gpio pins are grouped into 8-bit ports they can still be configured and accessed individually.
Each Port is associated with 2 registers for direction configuration(Input/Output) and for Read/Write.

Register Description
TRISx Used to configure the respective PORT as output/input
PORTx Used to Read/Write the data from/to the Port pins

note: Here 'x' could be A,B,C,D,E so on depending on the number of ports supported by the controller.

TRISx:TRI-State Register/ Data Direction Register
Before reading or writing the data from the ports, their direction needs to be set. Unless the PORT is configured as output, the data from the registers will not go to controller pins.

This register is used to configure the PORT pins as Input or Output. Writing 1's to TRISx will make the corresponding PORTx pins as Input. Similarly writing 0's to TRISx will make the corresponding PORTx pins as Output.

TRISB = 0xff;  // Configure PORTB as Input.
 
TRISC = 0x00; // Configure PORTC as Output.
 
TRISD = 0x0F; // Configure lower nibble of PORTD as Input and higher nibble as Output
 
TRISD = (1<<0) | (1<3) | (1<<6); // Configure PD0,PD3,PD6 as Input and others as Output



PORTx:
This register is used to read/write the data from/to port pins. Writing 1's to PORTx will make the corresponding PORTx pins as HIGH. Similarly writing 0's to PORTx will make the corresponding PORTx pins as LOW.
Before reading/writing the data, the port pins should be configured as InputOutput.

PORTB = 0xff;  // Make all PORTB pins HIGH.
 
PORTC = 0x00;  // Make all PORTC pins LOW..
 
PORTD = 0x0F;  // Make lower nibble of PORTD as HIGH and higher nibble as LOW 
 
PORTD = (1<<PD0) | (1<PD3) | (1<<PD6); // Make PD0,PD3,PD6 HIGH,
 
 
TRISB = 0x00;  // Configure PORTB as Output
TRISD = 0xff;  // Configure PORTD as Input
PORTD = PORTB; // Read the data from PORTB and send it to PORTD.



Led Blinking Example

After knowing how to configure the GPIO ports, its time to write a simple program to blink the Leds.
Below points needs to be considered for this example.

  • Include the io.h file as it has the definitions for all the PORT registers.
  • Include delay.h file to use the delay functions.
  • Configure the PORT as Output before writing any data to PORT pins.

Led Blinking Wiring Diagram

Blink bb.png



Led and Switches

LEDs and Switches Wiring diagram


Have a opinion, suggestion , question or feedback about the article let it out here!