In this tutorial we are going to discuss the Timer module of Pic16f877a.
First we will see what are timers, their working and later we will configure the PIC16f877a timers to generate delay of 100ms and 500ms respectively. At the end we will see how to use the ExploreEmdedded Timer library.

Timer Basics

As the name suggests these are used to measure the time or generate the accurate time delay. The microcontroller can also generate/measure the required time delays by running loops, but the timer/counter relieves the CPU from that redundant and repetitive task, allowing it to allocate maximum processing time for other tasks.

Timer is nothing but a simple binary counter that can be configured to count clock pulses(Internal/External). Once it reaches the Max value, it will roll back to zero setting up an OverFlow flag and generates the interrupt if enabled.

Timer.gif

PIC Timer Module

Pic16f877a has three indepenndent timer which can be used as timer,Counters or for PWM generation.
Below table provides the details of the three Timers.

Timer Size Control Register Count Register Min Delay Max Delay
TIMER0 8-bit OPTION_REG TMR0 0.2usec 13.107ms
TIMER1 16-bit T1CON TMR1H,TMR1L 0.2usec 104.857ms
TIMER2 8-bit T2CON TMR2 0.2usec 819usec

Timer Calculation

PIC Oscillator frequency is divided by 4 and then fed to the controller, Now this this freq can be further divided by presacalar to generate the range of delays.
Time to increment the Timer count by one(timer tick) can be determined as below.
tick = (Prescalar/(Fosc/4)
tick = (Prescalar/(20Mhz/4))
$$tick = (Prescalar * 4)/Fosc$$

Now the Timer value for the required delay can be calculated as below.
Delay = TimerCount * tick
Count = (Delay/tick)
RegValue = TimerMax- Count
RegValue = TimerMax-(Delay/tick) = TimerMax - (Delay/((Prescalar *4)/Fosc))
$$RegValue = TimerMax-((Delay * Fosc)/(Prescalar*4))$$

Below table provides the formula for all the three Timers.

Timer Size Formula for delay calculation
TIMER0 8-bit $$RegValue = 256-((Delay * Fosc)/(Prescalar*4))$$
TIMER1 16-bit $$RegValue = 65536-((Delay * Fosc)/(Prescalar*4))$$
TIMER2 8-bit $$RegValue = 256-((Delay * Fosc)/(Prescalar*4))$$



Timer 0

The TMR0 module is an 8-bit timer/counter with the following features:

  • 8-bit timer/counter
  • Readable and writable
  • 8-bit software programmable prescaler
  • Internal or external clock select
  • Interrupt on overflow from FFh to 00h
  • Edge select for external clock

Timer0 Registers

The below table shows the registers associated with PIC16f877A Timer0 module.

Register Description
OPTION_REG This registers is used to configure the TIMER0 Prescalar, Clock Source etc
TMR0 This register holds the timer count value which will be incremented depending on prescalar configuration
INTCON This register contains the Timer0 overflow flag(TMR0IF) and corresponding Inetrrupt Enable flag(TMR0IE).

OPTION_REG
7 6 5 4 3 2 1 0
RBPU INTEDG T0CS T0SE PSA PS2 PS1 PS0

RBPU: NA for Timers

INTEDG: NA for Timers

T0CS: TMR0 Clock Source Select bit
1-Transition on T0CKI pin
0-Internal instruction cycle clock (CLKO)

T0SE: TMR0 Source Edge Select bit
1-Increment on high-to-low transition on T0CKI pin
0-Increment on low-to-high transition on T0CKI pin

PSA: Prescaler Assignment bit
1-Prescaler is assigned to the WDT
0-Prescaler is assigned to the Timer0

PS2:PS0: Prescaler Rate Select bits Timer0Prescalar.png

  • Note:There is only one prescaler available which is mutually exclusively shared between the Timer0 module and the Watchdog Timer. A prescaler assignment for the Timer0 module means that there is no prescaler for the Watchdog Timer and vice versa. This prescaler is not accessible but can be configured using PS2:PS0 bits of OPTION_REG.



INTCON
7 6 5 4 3 2 1 0
GIE PIE TMR0IE INTE RBIE TMR0IF INTF RBIF

GIE: Global Interrupt Enable bit
1-Enables all unmasked interrupts
0-Disables all interrupts

PIE: Peripheral Interrupt Enable bit
1-Enables all unmasked peripheral interrupts
0-Disables all peripheral interrupts

TMR0IE: TMR0 Overflow Interrupt Enable bit
1-Enables the TMR0 interrupt
0-Disables the TMR0 interrupt

INTE: NA for Timers

RBIE: NA for Timers

TMR0IF: TMR0 Overflow Interrupt Flag bit
1-TMR0 register has overflowed (must be cleared in software)
0-TMR0 register did not overflow

INTF: NA for Timers

RBIF: NA for Timers
Timer0 Block Diagram.png


Delay Calculations for 1ms @20Mhz with Prescalar as 32: <math>RegValue = 256-(Delay * Fosc)/(Prescalar*4)) = 256-((1ms * 20Mhz)/(32*4)) = 256-156=100</math>

Code

Below are the steps for configuring and using the Timer0 for delay generation:

  1. Calculate the Timer Count for the required delay.
  2. Set the Presaclar bits in OPTION_REG as per the delay calculations.
  3. Clear the PSAbit for using the prescalar.
  4. Select the Clock Source Internal/External using TOCS bit.
  5. Load the timer value into TMRO register.
  6. Enable the Timer0 Interrupt by setting TMR0IE bit
  7. Enable the Global and Peripheral interrupts by setting GIE and PIE bits

Below is the sample code to blink the LEDs with 1ms delay. Delay measured using CRO: Timer0 Cro.png




Timer 1

The timer TMR1 module is an 16-bit timer/counter with the following features:

  • 16-bit timer/counter with two 8-Bit register TMR1H/TMR1L
  • Readable and writable
  • software programmable prescaler upto 1:8
  • Internal or external clock select
  • Interrupt on overflow from FFFFh to 00h
  • Edge select for external clock

Timer1 Registers

The below table shows the registers associated with PIC16f877A Timer1 module.

Register Description
T1CON: This registers is used to configure the TIMER1 Prescalar, Clock Source etc
TMRIH This register holds the higher 8-bits of timer value. TMR1H and TMR1L are used in pair to increment from 0000 - FFFFh
TMRIL This register holds the lower 8-bits of timer value. TMR1H and TMR1L are used in pair to increment from 0000 - FFFFh
PIR1 This register contains the Timer1 overflow flag(TMR1IF).
PIE1 This register contains the Timer1 Interrupt Enable flag(TMR1IE).

T1CON
7 6 5 4 3 2 1 0
T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON

T1CKPS1:T1CKPS0:Timer1 Input Clock Prescale Select bits
11 = 1:8 prescale value
10 = 1:4 prescale value
01 = 1:2 prescale value
00 = 1:1 prescale value

T1OSCEN: Timer1 Oscillator Enable Control bit
1-Oscillator is enabled
0-Oscillator is shut-off

T1SYNC: Timer1 External Clock Input Synchronization Control bit
1-Do not synchronize external clock input
0-Synchronize external clock input

TMR1CS: Timer1 Clock Source Select bit
1-External clock from pin RC0/T1OSO/T1CKI (on the rising edge)
0-Internal clock (FOSC/4)

TMR1ON: Timer1 On bit
1-Enables Timer1
0-Stops Timer1

Timer1 Block Diagram.png


Delay Calculations for 100ms @20Mhz with Prescalar as 8: $$RegValue = 65536-(Delay * Fosc)/(Prescalar*4)) = 65536-((100ms * 20Mhz)/(8*4)) = 3036 = 0xBDC$$

Code

Below are the steps for configuring and using the Timer1 for delay generation:

  1. Calculate the Timer Count for the required delay.
  2. Set the Presaclar bits in T1CON as per the delay calculations.
  3. Select the Clock Source Internal/External using TMR1CS bit.
  4. Load the timer value into TMR1H,TMR1L register.
  5. Enable the Timer1 Interrupt by setting TMRIE bit
  6. Enable the Global and Peripheral interrupts by setting GIE and PIE bits
  7. Finally start the timer by setting TMR1ON bit

Below is the sample code to blink the LEDs with 1ms delay. Delay measured using CRO: Timer 1 Cro.png




Timer 2

The TImer2 module is an 8-bit timer/counter with the following features:

  • 8-bit timer/counter
  • Readable and writable
  • Software programmable prescaler/PostScaler upto 1:16
  • Interrupt on overflow from FFh to 00h


Timer2 Registers

The below table shows the registers associated with PIC16f877A Timer0 module.

Register Description
T2CON This registers is used to configure the TIMER2 Prescalar, Clock Source etc
TMR2 This register holds the timer count value which will be incremented depending on prescalar configuration
PIR1 This register contains the Timer2 overflow flag(TMR2IF).
PIE1 This register contains the Timer2 Interrupt Enable flag(TMR2IE).

T2CON
7 6 5 4 3 2 1 0
TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0

TOUTPS3:TOUTPS0: Timer2 Output Postscale Select bits
0000 = 1:1 postscale
0001 = 1:2 postscale
0010 = 1:3 postscale



1111 = 1:16 postscale

TMR2ON: Timer2 On bit
1-Timer2 is on
0-Timer2 is off

T2CKPS1:T2CKPS0: Timer2 Clock Prescale Select bits
00 = Prescaler is 1
01 = Prescaler is 4
1x = Prescaler is 16

Timer2 Block Diagram.png


Generating 1sec delay using Timer2:
As the timer2 is 8-bit and supports 1:16 prescalar, it is not possible to directly generate the delay of 1sec. The max delay with 1:16 prescaler will be:
$$Delay = 256 * (Prescaler*4)/Fosc = 256 * 16*4/20Mhz=819us$$

Now 500us can be generated using timers which will be used to increment a counter 2000 times to get 1sec delay.
Delay Calculations for 500usec @20Mhz with Prescalar as 16: $$RegValue = 256-(Delay * Fosc)/(Prescalar*4)) = 256-((500us* 20Mhz)/(16*4)) = 256-156=100$$

Code

Below are the steps for configuring and using the Timer2 for delay generation:

  1. Calculate the Timer Count for the required delay.
  2. Set the Prescaler bits in T2CON as per the delay calculations.
  3. Load the timer value into TMR2 register.
  4. Enable the Timer2 Interrupt by setting TMR2IE bit
  5. Enable the Global and Peripheral interrupts by setting GIE and PIE bits
  6. Finally start the Timer2 by setting TMR2ON bit

Below is the sample code to blink the LEDs with 1sec delay. Delay measured using CRO: Timer 2 Cro.png

00 Lpc1768 Timer.jpg

Downloads

Download the complete project folder from the below link:
Hardware design Files and Code Library


Have a opinion, suggestion , question or feedback about the article let it out here!