The Explore Ultra 8051 Kit comes with all the things required, not just for this experiment but for the entire series. The base board is fully open, no peripheral is directly connected to the MCU breakout board. You may connect any peripheral to any port/pin you wish. The kit is fully open source, you may use the schematics, the design files and all of the source code and build something cool on your own. And when you do that do not forget to share with us what you've done. We would be happy to see you building something cool.

0ultra 8051.png

The story of the Ultra Kit does not end here, we have even made the code libraries for all major 8-bit microcontrollers modular. It means you can simple upgrade or even switch your project to a different microcontroller/architecture without changing your application code. The kit ships with all the additional stuff mentioned below to get you started; kickstart your embedded development. What are you waiting for?

Kit Contents: Explore ULTRA PIC Development Board with following Modules, ICs and Interfaces:

  1. USB Communication with CP2102
  2. Eight 5mm LEDs
  3. Eight Switches in DIP package
  4. LCD 16x2
  5. Four Seven Segment Displays
  6. ADC 0808 with 555 timer for sampling frequency
  7. POT for ADC
  8. Light Sensor(LDR).
  9. Temperature sensor(LM35).
  10. Two Relays for Switching AC devices.
  11. 4x4 Keypad.
  12. L293D Motor Driver for DC and Stepper Motors.
  13. DS1307 based Real Time Clock.
  14. AT2404 EEPROM.
  15. USB cable.
  16. Power Adapter
  17. Single wire female connectors.

Supported Controllers

Controller Flashing Software External Programmer Comments
At89s52 XploreFlash/ProgIsp UsbAsp Programmer IC is cheap and easily available but needs external programmer
P89v519d2 Flash Magic Not required, uses on board USB NXP has stopped manufacturing the IC and only the stock items are being sold.
SST8951RD2 Easy ISP Not required, uses on board USB IC is good but the programming software is not stable, doesn't save the configuration, needs manual reset and many other problems.
w78e052d Nuvoton ISP Not required, uses on board USB IC is cheap and good GUI for flasing the code. FLashing hex file takes less time compared to all



Driver Installation

Software Setup

  • Compiler Installation: Download and Install the Keil software from this link.
  • Check this tutorial for setting up the project to generate the .hex file.
  • Check this tutorial for Uploading Hex File Using Xplore Flash for AT89S52.
  • Check this tutorial for Uploading Hex File Using Nuvoton ISP..

Complete Board Test

The board is shipped with test software loaded in the controller. Connect the board to the System, Open the Serial Terminal and reset the Controller. Follow the below procedure to test all the peripherals.

GPIO Test

Connect the LED's, Buzzer and Relays to any of the port pins and observe the Led Blink, Buzzer-Beep, and Relay-Chattering . *Note:The Rx,Tx pins will not blink as they are controlled by CP2102(Usb2Serial). GpioTest.png
8051 GPIO Testing.png


LCD 8-bit Test

Below table shows the LCD 8-bit pin connection.

RS RW EN D0 D1 D2 D3 D4 D5 D6 D7
P0_0 P0_1 P0_2 P2_0 P2_1 P2_2 P2_3 P2_4 P2_5 P2_6 P2_7

Lcd8bit.png
8051 LCD 8-bit Test.png


LCD 4-bit Test

Below table shows the LCD 4-bit pin connection.

RS RW EN D0 D1 D2 D3 D4 D5 D6 D7
P0_0 P0_1 P0_2 P_NC P_NC P_NC P_NC P2_4 P2_5 P2_6 P2_7
  • P_NC: Pin Not Connected

Lcd4bitTestCode.png
8051 LCD 4-bit Test.png

Seven Segment Test

Below table shows the Seven Segment Connection.

Seg1 Seg2 Seg3 Seg4 a b c d e f g h
P0_0 P0_1 P0_2 P0_3 P2_0 P2_1 P2_2 P2_3 P2_4 P2_5 P2_6 P2_7

SevenSegmentTest.png
8051 SevenSegment.png

RTC Test

The DS1307 RTC pins are connected to P0 (SCL-P0.6,SDA-P0.7). RtcEeprom.png
8051 RTC Testing.png

EEprom Test

(A-Z) is written to EEPROM and then read it back. Same is transmitted on UART.
The AT24cxx Eeprom pins are connected to P0 (SCL-P0.6,SDA-P0.7). RtcEeprom.png
8051 Eeprom Test.png

Adc Test

Ultra Board has a Pot, LDR and a temperature sensor. ADC values from these sensors is read and transmitted on UART. Below table shows the sensor pin connection.

ADC DataBus(D0:D7) A B C ALE START EOC OE
P2(P2_0:P2_7) P1_0 P1_1 P1_2 P1_3 P1_4 P1_5 P1_6

Adc0809 Interafce.png 8051 ADC Test.png

Keypad Test

Below table shows the hex keypad Row-Col pin connection.

R1 R2 R3 R4 C1 C2 C3 C4
P2_0 P2_1 P2_2 P2_3 P2_4 P2_5 P2_6 P2_7

KeyPad.png
8051 Hex Keypad.png

Downloads

  • Download the design files and sample codes from this link
  • Download the Keil software from this link


Have an opinion, suggestion , question or feedback about the article let it out here!